Your Complete Plumbing Guide for Installing a Bathtub
Your Complete Plumbing Guide for Installing a Bathtub
Blog Article
Just how do you really feel in relation to Tools You Need to Install a New Bathtub ?
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
Installing a bath tub isn't precisely rocket science, but it does call for strong plumbing, carpentry, and sometimes, tiling abilities. Changing an old tub with a new one is also a moderately tough job. If the old bathtub is conveniently easily accessible, the job can relocate rapidly; if you have to open up a wall to eliminate the old tub as well as position the brand-new bathtub, the job is much harder. In either instance, the project is within a house handyman's skills, although you will need a helper to vacate the old tub and also embeded in the new one. See to it you have qualified on your own for the work and are comfortable trying it. As opposed to hiring a specialist to take over a halfway-completed job, it is far better to consider employing one before you begin. Chances are you might require a specialist plumber to make tube connections.
This article will help you install a new bathtub in your shower room if you have actually currently bought a new bathtub and also don't need to alter the setup of your previous water supply pipelines.
Your devices and material list need to comprise the following:
Planning for the Installation
First of all, the sustaining frame supplied with the bathroom needs to be fitted (if required) according to the maker's directions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is necessary to ensure that if the faucet includes a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the faucets unit to avoid stress on the bathtub.
Fit the versatile faucet adapters to the bottom of both taps utilizing 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you make use of every one of the provided washers.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath ought to currently prepare to be fitted in its last position.
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you ought to do is separate the water system. After doing so, switch on the faucets to drain pipes any water staying in the system. The process of eliminating the existing faucets can be fairly troublesome because of the limited gain access to that is usually the case.
Use a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipes to the faucets. Have a towel all set for the remaining water that will come from the pipelines. As soon as the supply pipelines have actually been removed, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from turning during this procedure. When the taps have been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old securing compound.
Prior to carrying on to fit the brand-new taps, contrast the pipe links on the old faucets to the new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the brand-new taps to fit.
Setting up the Bath tub
Utilizing both wooden boards under its feet, position the bathtub in the called for placement. The wood boards are helpful in equally spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto four small points.
The following objective is to ensure that the bathtub is leveled all round. This can be attained by examining the level and adjusting the feet on the bath tub till the spirit level reads degree.
To mount taps, fit the bottom of the outermost adaptable faucet connector to the appropriate supply pipe by making a compression sign up with; after that do the same for the various other tap.
Switch on the water supply as well as check all joints and also new pipework for leakages and tighten them if essential. Fill the bath tub as well as also inspect the overflow electrical outlet as well as the normal electrical outlet for leaks.
Ultimately, deal with the bath paneling as described in the manufacturer's user's manual. Tiling as well as securing around the bathtub must wait up until the bath tub has been utilized at the very least when as this will resolve it right into its final position.
Fitting New Taps
If the tails of the new taps are plastic, after that you will certainly need a plastic port to avoid damages to the thread. One end of the port fits on the plastic tail of the tap and the other end supplies a link to the existing supply pipes.
If you need to fit a monobloc, then you will certainly need minimizing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, place the faucet in the mounting opening in the bath/basin ensuring that the washing machines are in place in between the faucet and the sink. Safeguard the faucet in place with the supplier supplied backnut. Once the tap is firmly in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular tap connectors. The previous type ought to be attached to the tap ends first, tightening only by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the location where the bathroom fulfills the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to fracture an inflexible seal, creating the water to pass through the wall surface between the bath and the tiling, leading to complications with dampness and also feasible leaks to the ceiling below.
You can pick from a selection of coloured sealants to assimilate your fixtures and fittings. They are marketed in tubes as well as cartridges, and can sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched paper or soft rope. Bear in mind to always load the tub with water prior to sealing, to enable the activity experienced when the tub remains in usage. The sealer can crack relatively very early if you do not take into consideration this motion before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly readily available on the marketplace. It is advisable to fit the tiles using water-resistant or water resistant sticky and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I found that blog posting on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround while doing a lookup on the search engines. Make sure you take the time to distribute this blog post if you enjoyed reading it. Thanks for going through it.
Immediate resolution offered. Report this page